品牌：美国 OSI

 

型号：CTCR

 

类型：电流传感器

 

非接触、环路供电、真有效值

描述DESCRIPTION

CTCR系列传感器提供了一种非接触、回路供电的电流测量方法。直流输出与交流窗口电流的真实RMS值成正比。测量范围为1A至100A。

The CTCR series of transducers provides a non-contact,loop-powered, method of current measurement. The dc output is directly proportional to the true RMS value of ac window current. Measurement ranges of 1A to 100A are available.

特征/FEATURES

•±0.25%的准确度（1A型为±0.5%）

•真实有效值测量

•非接触式

•环路供电

•易于安装

• ±0.25% accuracy (±0.5% on 1A model)

• True RMS measurement

• Non-contact

• Loop-powered

• Ease of Installation

参数

电流输入	0-100Aac
输出	4-20mAdc回路
准确性	±0.5% FS，±0.25% FS
频率	50-400Hz
测量	交流电
核心类型	实芯
安装	控制板
系统配置	1Ø

型号选择

输入交 流电流	标准输出型号CTCR
	（4-20mAdc环路供电）
0-1	001E2
0-5	005E2
0-10	010E2
0-15	015E2
0-20	020E2
0-25	025E2
0-30	030E2
0-35	035E2
0-40	040E2
0-50	050E2
0-100	100E2

规格参数

输入INPUT
电流范围Current Range			0-100Aac
超范围无损坏	连续的			1.3倍额定值
瞬态（10秒/小时）Transient (10s/hr)			5倍额定值
频率范围Frequency Range			50-400Hz
输出OUTPUT
类型	2线			4-20mAdc，环路供电
缩放比例			0-F.S.输入=4-20mAdc输出
装载	24Vdc回路电源				0-500Ω
	15Vdc回路电源				0-400Ω
响应	至90%				250毫秒，典型
波纹			≤1.0%F.S.峰值
介电测试DIELECTRIC TEST
导体通过窗口输出 Conductor Through Window to Output			2200Vac
仪表功率INSTRUMENT POWER
环路供电	名义值				24Vdc
范围			15-35Vdc
精度（设定值、线性、重复性）ACCURACY (setpoint, linearity, repeatability)
1A型号
50/60Hz	10-100%F.S			±0.5%F.S.
其它			±2%F.S.，典型5A-100A型号
50/60Hz	10-100%F.S			±0.25%F.S.
其它			±1%F.S.典型
温度TEMPERATURE
操作		范围				-20°C~60°C
影响			±1.0%F.S.
物理性能PHYSICAL
终端			6-32号螺丝端子
重量Weight			0.2LB

安装/操作/保修/INSTALLATION / OPERATION / WARRANTY

 

安装说明/INSTALLATION INSTRUCTIONS

1.只能由合格的电工进行安装！

2.在进行任何电气连接之前，确保电气服务已断开。

3.支路保护按国家和地方规范要求设置检查机构的报告。

4.按要求布线，并按照本表和装置上的接线图固定到端子上。

5.传感器适合安装在600Vac线路上。

6.为防止与带电电路接触，当安装在裸母线上时，要求传感器安装在需要使用工具进入的外壳中。当安装在绝缘电缆上时不需要第二个外壳的电缆。

1. Installation should be performed by qualifi ed electricians only!

2. Make sure electrical service is disconnected before making any electrical connections.

3. Branch circuit protection is required to be provided in accordance with the National and Local codes of the inspection authority.

4. Route wires as required and secure to terminals per connection diagram on this sheet and on the unit.

5. Transducers are suitable for installation on 600Vac lines.

6. To prevent contact with live circuits, when installed on a bare bus bar, the transducer is required to be mounted in an enclosure that requires the use of a tool for access. When installed on an insulated cable this second enclosure is not required.

 

 

操作说明/OPERATING INSTRUCTIONS

1.本装置适用于海拔2000米以下的室内使用。

2.根据安装类别（过电压）II，污染等级2的瞬态过电压。

3.如果需要清洁外表面，则应断电所有供应服务（两个测量和仪表电源电路），并用软刷刷洗或用低压空气吹扫。使用适当的眼部保护。不适合清洗软管。

4.最高相对湿度80%，温度最高31ºC，线性下降至50% 40℃时的相对湿度。

5.最大工作温度范围为-20°C至60°C。

1. This unit is intended for indoor use at altitudes up to 2000 meters.

2. Transient overvoltages according to Installation Category (overvoltage) II, Pollution Degree 2.

3. If cleaning of the exterior surface is necessary, de-energize all services of supply (both measuring and instrument power circuits) and brush with a soft brush or blow off with low-pressure air. Use appropriate eye protection. Not suitable for hose-down cleaning.

4. Maximum relative humidity 80 percent for temperatures up to 31ºC decreasing linearly to 50 percent relative humidity at 40ºC.

5. Maximum operating temperature range is -20°C to 60°C.