产品类别
称重测力传感器
8455新葡萄娱集团am及变送器
速度及加速度传感器
料/液位计
位移传感器
扭矩传感器
温湿度传感器,变送器
显示控制仪表
记录仪
整列机
测力系统
微粒子检测仪
激光器
流量传感器/开关
陀螺仪
引伸计
频闪仪
变送器/放大器/接线盒
变频器
编码器
试验机
数据采集器
角度传感器
声级计
振动计
多通道分析仪
流量计
电子衡器
实验室设备
水分分析仪
质量流量计
测试分析系统
模块型仪表
静电纺丝机
高速数据采集卡
Tinius Olsen测试设备
试验机
信号调理器
Sirius数据采集系统
切割设备
三维扫描仪
示波器
水听器
功率放大器
安全保持器
温度计监视器
振动增幅器
人像表面温度热像仪
温度检查器
红外线 辐射温度仪
红外多分析仪
FC评价试验装置
电缆
加速度传感器
碳气溶胶组分在线分析系统
黑碳仪
接线盒
显示器
隔离器/转换器
打印机
拧紧机
液氮罐
CTS-150R电流传感器
品牌:美国 OSI
型号:CTS-150R
类型:电流传感器
特点FEATURES
•易于安装
•分芯
•现场可选输入:25,75100150A
•方便的10Vdc输出
•重量轻(8盎司)
• Easy Installation
• Split-core
• Field selectable inputs: 25,75,100,150A
• Convenient 10Vdc output
• Lightweight (8oz.)
应用APPLICATIONS
•负载监测
•控制系统
•建筑物管理
•过程自动化
•分支机构监测
• Load Monitoring
• Control Systems
• Building Management
• Process Automation
• Branch Monitoring
参数
电流输入 |
可选:0-25Aac、0-75Aac、0-100Aac、150Aac |
输出 |
0-10Vdc |
准确性 |
±1.0% FS |
频率 |
50-60Hz |
测量 |
交流电 |
核心类型 |
分裂核心 |
安装 |
控制板 |
系统配置 |
单相 |
规格参数
输入INPUT |
|||||
电流Current |
范围 |
可选:0-25/75/100/150Aac |
|||
无损坏的过电流Over-current w/o damage |
10秒.@4倍额定值 |
||||
频率范围Frequency Range |
50/60Hz |
||||
输出OUTPUT |
|||||
范围Range |
满量程:0-10Vdc |
||||
载入Loading |
≥10kΩ |
||||
响应(至90%)Response . (to 90%) |
≤200秒 |
||||
波纹Ripple |
≤1.0% F.S. |
||||
测量类型MEASUREMENT TYPE |
RMS |
||||
精度(任何范围选择) ACCURACY (any range selection) |
±1.0% F.S. |
||||
仪表功率INSTRUMENT POWER |
24Vdc,±10% |
||||
电介质DIELECTRIC |
(耐电压) |
3500V, 60Hz, 1min. |
|||
环境性能ENVIRONMENTAL |
|||||
工作温度范围Operating RangeTemperature |
-40~70ºC |
||||
影响Effect |
典型0.01%/摄氏度 |
||||
存储范围StorageRange |
-45 to 85ºC |
||||
工作湿度Relative Humidity |
0-95%,不冷凝 |
||||
物理性质PHYSICAL |
|||||
重量Weight |
8盎司 |
||||
连接Connections |
飞线,6英尺,22AWG,剥皮和镀锡 |
||||
附件Enclosure |
聚酰胺尼龙,UL94V-0,黑色 |
||||
开启角度Opening Angle |
180° |
输入和输出范围选择
安装/操作/保修/INSTALLATION / OPERATION / WARRANTY
安装说明/INSTALLATION INSTRUCTIONS
1.只能由合格的电工进行安装!
2.在进行任何电气连接之前,确保电气服务已断开。
3.支路保护按国家和地方规范要求设置检查机构的报告。
4.按要求布线,并按照本表和装置上的接线图固定到端子上。
5.传感器适合安装在600Vac线路上。
6.为防止与带电电路接触,当安装在裸母线上时,要求传感器安装在需要使用工具进入的外壳中。当安装在绝缘电缆上时不需要第二个外壳的电缆。
1. Installation should be performed by qualifi ed electricians only!
2. Make sure electrical service is disconnected before making any electrical connections.
3. Branch circuit protection is required to be provided in accordance with the National and Local codes of the inspection authority.
4. Route wires as required and secure to terminals per connection diagram on this sheet and on the unit.
5. Transducers are suitable for installation on 600Vac lines.
6. To prevent contact with live circuits, when installed on a bare bus bar, the transducer is required to be mounted in an enclosure that requires the use of a tool for access. When installed on an insulated cable this second enclosure is not required.
操作说明/OPERATING INSTRUCTIONS
1.本装置适用于海拔2000米以下的室内使用。
2.根据安装类别(过电压)II,污染等级2的瞬态过电压。
3.如果需要清洁外表面,则应断电所有供应服务(两个测量和仪表电源电路),并用软刷刷洗或用低压空气吹扫。使用适当的眼部保护。不适合清洗软管。
4.最高相对湿度80%,温度最高31ºC,线性下降至50% 40℃时的相对湿度。
5.最大工作温度范围为-20°C至60°C。
1. This unit is intended for indoor use at altitudes up to 2000 meters.
2. Transient overvoltages according to Installation Category (overvoltage) II, Pollution Degree 2.
3. If cleaning of the exterior surface is necessary, de-energize all services of supply (both measuring and instrument power circuits) and brush with a soft brush or blow off with low-pressure air. Use appropriate eye protection. Not suitable for hose-down cleaning.
4. Maximum relative humidity 80 percent for temperatures up to 31ºC decreasing linearly to 50 percent relative humidity at 40ºC.
5. Maximum operating temperature range is -20°C to 60°C.