TBS-25LB称重模块PDF资料：

品牌：美国Transducer Techniques

型号：TBS-25LB~40LB

类别：称重模块

 

 

型号	量程(lb)
TBS-.25LB	.25
TBS-.50LB	.50
TBS-1LB	1
TBS-2LB	2
TBS-5LB	5
TBS-10LB	10
TBS-20LB	20
TBS-40LB	40

 

 

TBS系列薄光束传感器特别适合小负载测量。它们被设计成测量发现的许多不同参数在医疗器械，家用电器，过程控制、机器人技术、汽车等其他高容量应用。特别的开发的集成应变计包括平衡、补偿和导电元件并叠层到梁上，以提供良好的稳定性和可靠性。

The TBS Series thin beam sensorsareexceptionallysuitedforsmallloadmeasurements. Theyaredesignedtomeasuremanydifferentparametersfoundinmedicalinstrumentation, home appliances, process control, robotics, automotive and manyother high volume applicatons. A speciallydeveloped integrated strain gage includes all

balancing, compensating and conductive elementsand is laminated to the beam to provide excellent stability and reliability.

 

 

 

 

规则参数：

额定输出Rated Output (R.O.) ・・・・・・・・・・・・・・・・ 2mV/V 

综合误差Combined Error ・・・・・・・・・・・・・・・・・・0.25% 满标度

零点平衡Zero Balance ・・・・・・・・・・・・・・・・・・・ ±0.3mV/NV 

补偿温度范围Compensated Temp. Range・・・・・・・・・・・ 20°to 120°F
温度效应Temperature Effects ・・・・・・・・・・・・・・・・ 零点平衡0.02% FS/°F

                        输出0.02%/°F
电阻Resistance ・・・・・・・・・・・・・・・・・・・・・・ （输入和输出）

                        1200欧姆±300欧姆

绝缘电阻Insulation Resistance ・・・・・・・・・・・・・・・ 50 VDC时为1000

励磁电压Excitation Voltage ・・・・・・・・・・・・・・・・ 10VDC

包装Seal ・・・・・・・・・・・・・・・・・・・・・・・・ 聚氨酯涂层

安全过载safe Overload ・・・・・・・・・・・・・・・・・・ 150% of R.O.

满标度偏转Full Scale Deflection ・・・・・・・・・・・・・・・ 0.010至0.0500

引线Lead Wire ・・・・・・・・・・・・・・・・・・・・・・ 9屏蔽PVC四导线30 AWG

材质Material ・・・・・・・・・・・・・・・・・・・・・・・ 301 SS（铍）铜1/4和1/2磅

偏转英寸Deflection Inches ・・・・・・・・・・・・・・・・・ .025

配件

型号	安装
TBS-MK-1	TBS-.25~TBS-5
TBS-MK-2	TBS-10~TBS-40

接线

+EXC.	RED
-EXC.	BLACK
+SIG.	GREEN
-SIG.	WHITE

尺寸

型号	量程(lb)	尺寸	对应尺寸图
TBS-.25lb	.25	0.006	Fig.1
TBS-.50lb	.50	0.009	Fig.1
TBS-1lb	1	0.011	Fig.1
TBS-2lb	2	0.015	Fig.1
TBS-5lb	5	0.022	Fig.1
TBS-10lb	10	0.031	Fig.2
TBS-20lb	20	0.044	Fig.2
TBS-40lb	40	0.063	Fig.2

薄梁力传感器的安装注意事项

INSTALL .ATION CONSIDERATIONS FOR THIN BEAM FORCE SENSORS

 

安装TBS-MK-1和TBS-MK-2时，必须仔细考虑设计因素系列细梁力传感器。传感器的性能取决于机械接口，都很薄。如下图1所示，梁式8455新葡萄娱集团am需要安装夹具，以便在加载过程中产生双重弯曲，这个图示被夸大，以显示夹具在产生相反力矩时的有效性，从而产生双弯，当双弯板在轴上产生张力和压缩时，会产生电输出传感器。

Careful design considerations must be taken into account when mounting the TBS-MK-1andtheTBS-MK-2Seriesthinbeamforcesensors.Thesensor'sperformance is dependent upon the mechanical interface. All thinbeam load cells require mounting clamps to create a double bend during loading as shown in figure 1. Thisillustration is exaggerated to show the clamp's effectiveness in producing opposing moments that create thedouble bend. An electrical outputisgenerated as the double bend causes tension and compression on thesensor.

两种典型的安装布置如下图所示：对于高精度应用，加强板应比梁材料稍硬，接口角应锋利，由于低负荷与TBS-.25至TBS-2相关的传感器结构，不建议使用在线加载（图2）。

Twotypicalmountingarrangementsareshownbelow.Forhighaccuracyapplications, reinforcement platesshould be slightly harder than the beam material, and the interfacing corners should be sharp. Due to low loadsand sensor construction associated with theTBS-.25thruTBS-2,inlineloading(Type2 )isnotrecommended.

 

TBS MK-1安装套件/TBS MK-1 Mounting Kit

 

安装套件TBS-MK-1仅适用于薄光束传感器TBS-.25至TBS-5型安装。套件包括：安装A、B和C区（以下尺寸单位为英寸）。

Mounting Kit TBS-MK-1 for thinbeamsensorsTBS- .25,thruTBS-5Type1Mounting Only. Kit includes: Mountingblocks A, B, & C (Dimensions below are in inches).

TBS MK-2安装套件/TBS MK-2 Mounting Kit

 

用于薄光束传感器TBS-10至TBS-40的安装套件TBS-MK-2。套件包括4个安装块，每个2个A区和B区（以下尺寸单位为英寸）。

Mounting Kit TBS-MK-2 for thin beam sensors TBS-10 thru TBS-40. Kit includes 4 mounting blocks, 2 of eachblock A & B (Dimensions below are in inches).